• Chapter 1 Simple Introduction
• Chapter 2 System Requirement
  • 2.1 Hardware
  • 2.2 Software
  • 2.3 Network connection settings
• Chapter 3 Hardware Description
  • 3.1 Hardware installation block diagram
  • 3.2 Ultrasonic Driver UD2H
    • 3.2.1 UD2H appearance
    • 3.2.2 UD2H specification
    • 3.2.3 Setting up
  • 3.3 Computer connection method
    • 3.3.1 Computer System Environment
• Chapter 4 Software Description
  • 4.1 Software introduction
  • 4.2 Software installation block diagram
  • 4.3 Software installation
    • 4.3.1 Main screen
  • 4.4 Software Use
  • 4.5 Operation mode
    • 4.5.1 PLC
    • 4.5.2 Digital
    • 4.5.3 Operation history
    • 4.5.4 Alarm list
  • 4.6 Function
    • 4.6.1 Settings
    • 4.6.2 PLC
    • 4.6.3 Ethernet
  • 4.7 Software Uninstall
• Chapter 5 Network connection setting
  • 5.1 Direct connection
  • 5.2 Remote Support

HiUD internal user manual

---

Chapter 1 Simple Introduction

• This HMI(Human Machine Interface) software HiUD is used to make an additional functional control and drive system analysis of ultrasonic driver UD2H. HIUD can turn on or off the ultrasonic funciton UD2H, adjust the output power, tool characteristics diagnostic and custom frequency output, and adjust the use of parameters such as ultrasonic drives. A alert will be recorded on the way of the operation process and the monitoring the drive.

圖 1 HiUD user interdace

Chapter 2 System Requirement

• The following is divided into three chapters to explain the relevant environment settings that use this software need.

item	Name	Version
Hardware	UD2H	3.12
Software	HiUD	1.2.0

2.1 Hardware

• Hardware devices need to be used
  • UD2H ultrasonic driver
  • Ultrasonic knife
  • Personal computer

2.2 Software

• Program and software kit need to be used
  • HiUD
  • dotNetFramework

2.3 Network connection settings

• Software use
• Remote support

Chapter 3 Hardware Description

3.1 Hardware installation block diagram

• The environmental connection is shown in the following figure.

Figure 3.1 Hardware connection diagram

• The actual connection photo is as follows (The following are offline operation, the connection method on the machine is also the same).
  
  

Figure 3.2 Setting environment

Figure 3.1 UD2H ultrasonic driver

Figure 3.1 Testing tool holder and power transmitter

Figure 3.1 HiUD execution Interface

3.2 Ultrasonic Driver UD2H

3.2.1 UD2H appearance

• The ultrasonic driver UD2H body is shown below.
  
  

Figure 3.2 Front side view

Figure 3.3 Back side view

3.2.2 UD2H specification

Table 3.1 UD2H specification sheet

Item	Specification
Power	60 W
Frequency range	20k~32 kHz
Driver power supply	AC 100~240 V, 50/60Hz, single-phase.
PLC power supply	DC 24 V
Temperature	Operating: -20 °C to 50 °C Transportation and storage: -25 °C to 60 °C
Humidity	operating: 5 % RH–95 % RH, (Non-condensation) Transportation and storage: 5 % RH–95 % RH, (Non-condensation)
Dimension	Wall-mount board 1. Include(LxWxH): 280x215x162 mm 2. Exclude(LxWxH)： 370x215x162 mm
Weight	4.2 kg
Function	1. Wisdom scanning various tools. 2. Automatic locking and chase frequency. 3. Output power adjustment. 4. Variety of control modes (Manual / PLC / Ethernet). 5. Ultrasonic information display and output. 6. Variety of alert messages.

• External control box
  • Ultrasonic Driver UD2H Support Control Box Remote Control Mode, the operation method is the same as the front side of the body; use the signal line to connect the external control side D-type connector.
    
    

Figure 3.4 External control box front view

Figure 3.5 External control box side view

Figure 3.6 External control box signal line

• IO
  
  

Figure 3.7 UD2H Front panel

Figure 3.8 UD2H Front panel

3.2.3 Setting up

• Installing the ultrasonic driver UD2H by following steps:
  1. Connect the power cord.
  2. Connect the power line.
  3. The power line is connected to the power transmitter (in the figure, the power transmitter is only a schematic diagram, please install the tool holder to the corresponding transmitter).
  4. Connect the network line.
  5. The other end of the network is connected to the computer.

Figure 3.9 Connecting Power Cord

Figure 3.10 Connecting Power Line

Figure 3.11 Ultrasonic power transmitter

Figure 3.12 Connecting Network line

Figure 3.13 Connecting to computer

3.3 Computer connection method

• This side is described here, as shown in the steps below:
  1. Prepare USB to ethernet card.
  2. The computer is plugged in USB to the ethernet card.
  3. Use the network cable to the UD2H ultrasonic driver.
     
     

Figure 3.14 USB to ethernet Card

Figure 3.15 USB to ethernet card connectting to computer

Figure 3.16 USB to ethernet card connectting with network line

3.3.1 Computer System Environment

Table 3.2 System Environment Requirement

	Necessary	Suggest
CPU	1.60 GHz	1.60 GHz or above
RAM	8 GB	8 GB or above
Hard disk	256 GB	256 GB or above
Display	Integrated graphics processors	Integrated graphics processors
OS	windows 10	windows 10 x64

Chapter 4 Software Description

4.1 Software introduction

• This HMI(Human Machine Interface) software HiUD is used to make an additional functional control and drive system analysis of ultrasonic driver UD2H. HIUD can turn on or off the ultrasonic funciton UD2H, adjust the output power, tool characteristics diagnostic and custom frequency output, and adjust the use of parameters such as ultrasonic drives. A alert will be recorded on the way of the operation process and the monitoring the drive.

4.2 Software installation block diagram

Figure 4.1 Software installation process

4.3 Software installation

• Use software installer to complete installation according to the guide; after the installation is complete, click on the desktop shortcut to execute.
• If it is unable to start after loading, it should be a lack of dotNetFramework kits, it can be downloaded by Microsoft's official website.
  • The download link is as follows:
    Windows version .NET Framework 4.6.1 Offline installer

4.3.1 Main screen

• Software main screen description:
  • The top left is the company logo.
  • The top right is the parameter setting option.
  • The bottom is the system status and operation tips.
  • Middle is displayed for operation and parameters.
    
    

圖 4.2 HiUD user interdace

4.4 Software Use

1. Follow the previous network connection guide to prepare the hardware device.
2. Go to the Windows desktop click HiUD shortcut to start the HIUD.
3. HiUD will first detect the ethernet card settings. If the it is not detected, the ethernet card will ask the user.
4. You can see that the system status column is ready, and then you can start using HIUD.

4.5 Operation mode

4.5.1 PLC

• Switch UD2H operation mode to PLC mode, use the machine IO point bit to control UD2H.

Figure 4.3 PLC mode

4.5.2 Digital

• Switch UD2H operation mode to ethernet mode, use your computer to control UD2H.

Figure 4.4 ethernet mode

4.5.3 Operation history

• In order to processing customer's problem, HiUD will record all operations and driving information return in the computer.

Figure 4.5 Operation history

4.5.4 Alarm list

• Record all occurred alarm message during operation.

Figure 4.6 Alarm list

4.6 Function

4.6.1 Settings

• Setting page can set display language and UD2H driving parameters.
  • Default
    • Hantop default optimizated UD2H driver parameters setting.
  • User
    • Provide 5 groups of UD2H drive parameters setting to users.

Figure 4.7 Setting page default tab

Figure 4.8 Setting page user tab

4.6.2 PLC

• Status
  • Show the current UD2H parameters and time accumulation charts.
• IO
  • Display a point information that is transferred by UD2H return information.

Figure 4.9 PLC mode status tab

Figure 4.10 PLC mode IO tab

4.6.3 Ethernet

• Status
  • Turn on or off the ultrasonic funciton, adjust the output power, display the current UD2H parameters and time cumulative charts, parameter data can be displayed or hidden using the selected box on the right.
• Diagnosis
  • Set the upper, lower limits and resolution of the frequency sweeping to analyze tool characteristic.
  • Output sweeping charts.
  • Sweep information output.
• Customize
  • Turn on or off the ultrasonic funciton, adjust the output frequency, adjust the output power function; display the current UD2H parameter and time accumulation chart.

Figure 4.11 Ethernet mode status tab

Figure 4.12 Ethernet mode status tab parameter display

Figure 4.13 Ethernet mode diagnosis tab

Figure 4.14 Ethernet mode custom output tab

4.7 Software Uninstall

• Go to the installation directory to select unistaller.
• Or enter the windows unistaller removal program.

Chapter 5 Network connection setting

5.1 Direct connection

• Insert the USB to ethernet card to laptop.

Figure 5.1 Connect to laptop

Figure 5.2 Connection network line

• Set the USB ethernet card IP to 192.168.0.201, as shown in the following table.

item	Content
IP	192.168.0.201
Mask	255.255.255.0

1. Setting/Network and Internet/Change adapter option.

Figure 5.3 Change the ethernet card setting.

2. Select the ethernet card that is now connected to the ultrasonic drive UD2H, right click.
   
   

Figure 5.4 Switch to the property.

3. 網路功能/網際網路通訊協定第4版(TCP/IPv4)/ 內容，一般/使用下列的IP位置。
4. Networking/ Internet Communication Agreement 4 (TCP / IPv4) / properties, typically / using the following IP adress.
   
   

Figure 5.5 Change the IPv4 IP adress.

4. Press the OK button to complete the IP change.

5.2 Remote Support

• Local network connection setting method is the same as 5.1.
• In addition, you need to install anydesk software on the supported computer.
  • AnyDesk software can be downloaded by official website:
    AnyDesk: The Fast Remote Desktop Application
• The connection is shown in the following figure.

Figure 5.6 Remote support connection diagram