---
# System prepended metadata

title: MOVE SYSML Model Notes

---

# MOVE SYSML Model Notes
## General
- Add pkg for Ground Segment (STR+Behavior) and move GS+Ops there :heavy_check_mark: 

## Feedback MOVE-III IBD Overview
### General
- Flow Items w/o name
- One BlackBoxView & one WhiteBoxView Diagram

### ADCS
- i2c and spi are data lines -> check if adcs is connected with i2c and spi or only can &rarr; only can
- imu -> check if imu is soldered on the adcs board &rarr; it is
- unlinked ports: vbat in -> no vbat in right now

### COM
- missing power &rarr; vbat is power
- gnd ports &rarr; ask com

### STR
- is a separation of the power flow necessary for such a basic design?

### CDH
- unlinked ports: vabt in &rarr; no vbat in
- define missing connections &rarr; which connections
- gns modulke included? &rarr; no maybe the L4

## MOVE-III Discussion w/ Designer
### ADCS
- ADCS Board Standard Connector + Subsystem Connector why? &rarr; look up in PDR/ask EPS (Is every SSb placed with all the unneccessary data and power ports?) - in the model SSB is 150% board, investigate if everything unecessary can be deleted, Switched Mode Power Supply SMPS part of ADCS? 
- VBAT for RW maybe - implemented
- Backplane - ADCS CAN 
- Power Sensor Magnetroquer and RW for sure, other PowerSensors not necessary as these parts don't draw that much power - EPS Design Descision
- ADCS Board Power deleted and in adcs subsystem - nope to much work/to big diagram
- BDot Daemon delete (ADCS Daemon controlls everything)
- Add daemon for every sensor and hardware
- Geomagnetic Field Flow


### DEDRA
- bdd Breakdown structure
    - idea feed is on the ssb, directly on the backplane
    - feeac 1 pcb per sensor
    - feeahv rather close to the sensor most probabaly in total 1 pcs
    
- bdd parts
    - sensor box: 180v instead of 100v
    - check hardware components package structure
    - adc: position tbd, currently on feed, in the future potentually on feeac
    - feed: ic=ion channel, gc =grid channel, nc = neutral channel, ec=electron channel &rarr; parts are not existing anymore, oszilator(not that important) and non volitaile flash memory is missing
    - fpga ports: in+out data 3 adcs quad spi, 3.3V, in+out: data & adress to SRAM, GND
    - feeahv: hv generation 5V instead of 3.3v; power converter located on every feeac (3x), produces out of 3,3V &rarr; 15V

- ibd dedra current 
    - feeahv pcb in dedra current diagram 
    - feed data: ic und ex amped siganl feeac instead of feed
    - feeac data correct, adc missing 
- SE Feedback 
    - FEEAC PCB bdd necessary? Is the high granity of the displayed parts necessary? Especially when it comes to ibds and Flows
    - What is this DEDRA FEE PCB Stack for? Which PCB is placed on the SSB?
    - 
 ### COM
 
 - Structure
     - Murgas one block + Power Sensor Murgas Module + 
         - 3.3V
         - RS485 (basically UART but tranceiver chip necessary)
         - RF Signal Antenna
         - Right now Murgas is on extra Dulta board, on final not (special connector)
     - RS485 Transceiver (UART, General I/O Port(transformed Signal))
         - Ibd current: connect to connector with 3.3V 
         
     - Delete: DCDC Step down converter, RF Frontend, RF Transceiver, Power Sensor for RF Front, Power Sensor RF Trans, Temp Sensor, Power Sensor for Temp Sensor
- Flows
    -  Com Board only with 3.3V connected to the Backplane

### CDH 
- Structure
    - power sensors optional
    - rtc battery
    - 
- Flows
    - fram+mram add in power idb (3v3)
    - gnss module power 3v3
    - can in + out to backplane
    - mram spi bidirectional
    - rtc bidirectional 3,3 v flow to battery 
- improvements: more detailed data lines for telemetry

### EPS

- structure
    - bcr board: no digital anlog converter + no microcontroller; simplify diagrams
    - no switch between bat board und backplane
    - backplane: model as it is categorized in altium 
    - Model SSB 
    
uvp manuel getriggert (reset pin)

pdr source for upgrades
(battery board und uvp nicht)


- SSB
    - Is there a power out at the MCU?
    - Check Ibd ADCS Board Power Overview
    - 