# Arduino Nano & Raspi4 教學
- 課程目的
- MCU基本介紹
- Sensor介紹
## 課程目的
藉由這堂課讓大家了解 Sensor 與 MCU 之間如何交流 , 並教導如何去了解Sensor整個工作原理 , 並使用熟悉的程式語言做到資料處理及通訊 , 完成功能後如何預防突發狀況 並加上需要的功能
## 課程章節
1 . 介紹arduino Sensor 與 實做
2 . Raspi環境設定完成(1 . 剛開機的設定 , 2 .SSH服務開啟 , 3 .MQTT )
3 . 寫python 轉介資料(serial & mqtt)
3.1 .在python code 上 寫serial reconnect
4 . Raspi安裝nodejs 並裝pm2 做服務管理
5 . Raspi上寫bashrc 把用pm2 執行python的指令
### 1 .介紹arduino Sensor 與 實做
#### 1 .Arduino IDE https://www.arduino.cc/en/Main/Donate
#### 1.2 .安裝教學 https://www.arduino.cc/en/Guide/Linux
#### 1.3 .MCU基本介紹
Arduino Nano , 比起Uno板 體積小 , 比起Pro mini 提供的電源較方便 , 且內建TTL晶片燒入
- 為何選Nano http://web.unumobile.com/unu/?p=77
- Pro mini燒入方式 http://mix-cat.blogspot.com/2016/02/arduino-mini-pro-tx-rx-5vgnd-reset.html
- Nano 的腳位介紹
#### 1.4 .Sensor介紹
- DHT22 AM2302 電容式溫濕度感測 由 熱敏電阻和濕度感測器 組成
- 熱敏電阻 由於溫度變化而變化, NTC 為負溫度係數
- 濕度感測器 由2個電極中間帶著濕度介質 當空氣中濕度變化 就會改變存電量 影響電阻的大小 (導電率)
- lib 有異常的 請到資料夾把你引入的lib砍掉 , 到這個連結下載並且引入 https://github.com/Kevin8701111/IoT-class/tree/master/arduino/dht22/lib
- 在google 搜尋dht22 library arduino 找到 https://www.arduinolibraries.info/libraries/dht-sensor-library 並下載最新版
#### 1.5 .實做Arduino sensor AM2302 DHT22
- 使用 剛剛匯入的 arduino-DHT-master 範例 https://www.arduino.cc/en/guide/libraries?setlang=cn
- 並完成溫濕度感測電路 
(DHT22) - Arduino
`DAT - D2`
`VCC - 5V`
`GND - GND`
- 將資料改成json格式
- json 格式檢查 http://json.parser.online.fr/
- 使用 \跳多字元 完成下面的格式
- {"Humidity":65,"temperature":21}
```
#include "DHT.h"
DHT dht;
void setup()
{
Serial.begin(9600);
dht.setup(2); // data pin 2
}
void loop()
{
float humidity = dht.getHumidity();
float temperature = dht.getTemperature();
if(dht.getStatusString() == "OK"){
Serial.print("{\"Humidity\":");
Serial.print(humidity, 1);
Serial.print(",\"Temperature\":");
Serial.print(temperature, 1);
Serial.print("}\n");
}
else{
Serial.print("sensor error");
}
delay(1000);
}
```
有錯的話改成下面的程式
```
#include "DHT.h"
#define dhtPin 2
#define dhtType DHT22
//#define dhtType DHT11
DHT dht(dhtPin, dhtType);
void setup(){
Serial.begin(9600);
dht.begin();
}
void loop(){
float h = dht.readHumidity();
float t = dht.readTemperature();
if (isnan(h)||isnan(t)){
Serial.print("無法讀取");
return;
}
Serial.print("{\"Humidity\":");
Serial.print(h, 1);
Serial.print(",\"Temperature\":");
Serial.print(t, 1);
Serial.print("}\n");
delay(1000);
}
```
### 2 .Raspi環境設定完成
#### 2 .Raspi4
- 開機後 請切出terminal (ctrl + alt + T)
- 設定Taipei , chinese , us鍵盤 都打勾
- 設定密碼 請全部使用 iotclass
- sudo apt-get update
- sudo apt-get install ssh
- sudo service ssh status
- sudo service ssh start (先做到這裡)
#### 2.1 .Linux Port permission https://arduino.stackexchange.com/questions/21215/first-time-set-up-permission-denied-to-usb-port-ubuntu-14-04
1 .`ls -l /dev/tty*`
2 .`sudo usermod -a -G dialout kevin(你自己的username)`
3 .`sudo chmod a+rw /dev/ttyUSB0`
4 .`SUBSYSTEMS=="usb-serial", TAG+="uaccess"`
5 .即可正常燒入
- 測試 file -> Examples -> 01Basic ->Blink
- 加入 library DHT22 -> Sketch -> include Library -> Add .ZIP Library -> 選擇你的library.zip檔
- 自定義tty https://www.twblogs.net/a/5bc10f2f2b717711c92423c3
#### MQTT 安裝
- sudo apt-get install mosquitto
- sudo apt-get install mosquitto-clients
- service mosquitto status
- mosquitto_sub -t KK
- mosquitto_pub -t KK -m "KKK"
### 3 .寫python 轉介資料
#### pyserial DATA get
``` python=
import serial
serial = serial.Serial('/dev/ttyUSB0',9600 , timeout = 2)
response = serial.readline()
```
#### MQTT Pub DATA
```python=
import paho.mqtt.publish as publish
publish.single("Sensor/DHT22", payload=response,
qos=0, hostname="127.0.0.1", port=1883)
```
#### MQTT DATA get
- 直接找python mqtt 範例code 複製貼上 https://pypi.org/project/paho-mqtt/
- 留下 on_connect , on_message 2個funtion
- 加上client.loop_forever()讓程式永遠執行
#### MQTT Sub DATA
```python=
import paho.mqtt.client as mqtt
import json
def on_connect(client, userdata, flags, rc):
client.subscribe("Sensor/DHT22")
def on_message(client, userdata, msg):
data = json.loads(str(msg.payload.decode('ascii')))
print(data)
client = mqtt.Client()
client.on_connect = on_connect
client.on_message = on_message
client.connect("192.168.1.138", 1883)
client.loop_forever()
```
### 3.1 .在python code 上 寫serial reconnect
#### MQTT pub 完整code
```python=
import serial
import time
import paho.mqtt.publish as publish
serial = serial.Serial('/dev/ttyUSB0',9600 , timeout = 2)
def readandpub(serial):
print('read')
response = serial.readline()
if response != '':
publish.single("Sensor/DHT22", payload=response,
qos=0, hostname="127.0.0.1", port=1883)
status = 1
else:
status = reconnect(serial)
return status
def reconnect(serial):
print('re')
try:
serial.close()
serial.open()
status = 1
return status
except:
status = 0
return status
while True:
try:
status = readandpub(serial)
time.sleep(1)
except:
status = 0
while(status == 0):
status = reconnect(serial)
print("Arduino is reconnect")
```
### 4 .Raspi安裝nodejs 並裝pm2 做服務管理
#### 2.2 pm2 服務管理
- 程序管理 https://kknews.cc/zh-tw/code/3a6pnay.html
### 5 .Raspi上寫bashrc 把用pm2 執行python的指令
#### 2.2 開機排程
- 開機並執行 sudo nano ~/.bashrc
`pm2 start /home/pi/github_class/IoT-class/raspi/data_tran_pub.py --name dht22-data-tran --interpreter /home/pi/py3iotclass_env/bin/python3`
## 功課
請完成 raspi port號 綁定 Arduino 並自訂port tty名稱
關鍵字 : raspi , arduino , port , 固定
### 6 .OpenSSL數位簽章
目前架構為 :
- PC Linux ubuntu 16.04(ca Server and mqtt broker)
- Raspi4 4g raspbian(node1 mqtt pub&sub)
- Raspi4 4g raspbian(node2 mqtt pub&sub)
在ca Server
```
#生成ca私鑰
openssl req -new -x509 -days 365 -sha256
Country Name (2 letter code) [AU]:TW
State or Province Name (full name) [Some-State]:Taichung
Locality Name (eg, city) []:Taichung
Organization Name (eg, company) [Internet Widgits Pty Ltd]:NCHU
Organizational Unit Name (eg, section) []:2111
Common Name (e.g. server FQDN or YOUR name) []:kevinc
Email Address []:自己的@gmail.com
```
```
#生成ca證書
openssl req -new -x509 -days 3650 -key ca.key -out ca.crt
Country Name (2 letter code) [AU]:TW
State or Province Name (full name) [Some-State]:Taichung
Locality Name (eg, city) []:Taichung
Organization Name (eg, company) [Internet Widgits Pty Ltd]:NCHU
Organizational Unit Name (eg, section) []:2111
Common Name (e.g. server FQDN or YOUR name) []:kevinc
Email Address []:自己的@gmail.com
```
生成server的私鑰
```
openssl genrsa -out server.key 2048
```
生成server端請求文件（.csr)
```
openssl req -new -out server.csr -key server.key
Please enter the following 'extra' attributes
to be sent with your certificate request
A challenge password []:
An optional company name []:
```
Sign in with Wallet
Connect another wallet