NMP Lab 3 - HackMD

--- title: NMP Lab 3 --- ## 1. VLSM: 70% ### Given a subnet 192.168.x.0/24, x is your group number, ### R100 IP is 172.168.1.254, R3's IP is 172.168.1.x, WAN: 172.168.1.0/24 ### Setup VLSM for LANs of S1~S6 for the following numbers of users: S1: 60, S2: 30, S3: 6, S4: 12, S5: 12, S6: 12 Go into Router5 and open CLI Router>en Router#conf t Router(config)#int fa0/0 Router(config-if)#ip addr 192.168.1.1 255.255.255.192 Router(config-if)#no sh Router(config-if)#int fa1/0 Router(config-if)#ip addr 192.168.1.65 255.255.255.224 Router(config-if)#no sh Router(config-if)#int fa4/0 Router(config-if)#ip addr 192.168.1.105 255.255.255.252 Router(config-if)#no sh Go into Router6 and open CLI Router>en Router#conf t Router(config)#int fa4/0 Router(config-if)#ip addr 192.168.1.106 255.255.255.252 Router(config-if)#no sh Router(config-if)#int fa0/0 Router(config-if)#ip addr 192.168.1.97 255.255.255.248 Router(config-if)#no sh Router(config-if)#int fa1/0 Router(config-if)#ip addr 192.168.1.113 255.255.255.240 Router(config-if)#no sh Router(config-if)#int fa5/0 Router(config-if)#ip addr 192.168.1.109 255.255.255.252 Router(config-if)#no sh Go into Router7 and open CLI Router>en Router#conf t Router(config)#int fa4/0 Router(config-if)#ip addr 192.168.1.110 255.255.255.252 Router(config-if)#no sh Router(config-if)#int fa0/0 Router(config-if)#ip addr 192.168.1.129 255.255.255.240 Router(config-if)#no sh Router(config-if)#int fa1/0 Router(config-if)#ip addr 192.168.1.145 255.255.255.240 Router(config-if)#no sh Router(config-if)#int fa6/0 Router(config-if)#ip addr 172.168.1.1 255.255.255.0 Router(config-if)#no sh Go into Router4 and open CLI Router>en Router#conf t Router(config)#int fa0/0 Router(config-if)#ip addr 172.168.1.254 255.255.255.0 Router(config-if)#no sh ### show these subnet routes Go into Router5 and open CLI Router(config-if)#do sh ip ro Go into Router6 and open CLI Router(config-if)#do sh ip ro Go into Router7 and open CLI Router(config-if)#do sh ip ro Go into Router4 and open CLI Router(config-if)#do sh ip ro ## 2. RIP 30% ### setup RIP-2 Go into Router5 and open CLI Router(config-if)#exit Router(config)#router rip Router(config-router)#v 2 Router(config-router)#network 192.168.1.0 Go into Router6 and open CLI Router(config-if)#exit Router(config)#router rip Router(config-router)#v 2 Router(config-router)#network 192.168.1.0 Go into Router7 and open CLI Router(config-if)#exit Router(config)#router rip Router(config-router)#v 2 Router(config-router)#network 192.168.1.0 Router(config-router)#network 172.168.1.0 Go into Router4 and open CLI Router(config-if)#exit Router(config)#router rip Router(config-router)#v 2 Router(config-router)#network 172.168.1.0 ### show RIP routes Go into Router5 and open CLI Router(config-router)#end Router#sh ip ro Go into Router6 and open CLI Router(config-router)#end Router#sh ip ro Go into Router7 and open CLI Router(config-router)#end Router#sh ip ro Go into Router4 and open CLI Router(config-router)#end Router#sh ip ro ### R100 ping R1's subnet Go into Router4 and open CLI Router#ping 192.168.1.0 ###### tags: `Network Management Practice` `CSnote`